Answers

  • 0
  • 0

Global concrete foaming agent market trend 2023-2029 Influence of Concrete Foaming Agent on Foam Concrete (2) by Newsmanysmileys

Chile's government is considering phasing in a proposed ban on glacial mining to limit projects high in the Andes by some big copper companies. Chile's constitutional assembly has approved a proposal to ban mining in glaciers, protected areas, and areas vital to protecting the country's water system.

Chile's mining minister, Marcela Hernando, said about 20 mines had been identified in protected areas, some close to glaciers, including Codelco's El Teniente and Andina projects and Anglo American Plc's Los Bronces project.

The new measures for glaciers and other protected areas will put about a fifth of Chile's copper concrete foaming agent prices are predicted to increase in the next few days.

3. The larger the bubble diameter, the better, should be more than 1mm 

The pore diameter should be the same as the bubble diameter. Some experts misleading the pursuit of a small foam aperture of 0.1mm, in fact, because of physical foaming if the bubble diameter is large, the stability of the foam cannot be made of foam concrete. The same raw material and formula, the same equipment and technology, just change the bubble diameter, the compressive strength of 1mm bubble diameter of foam concrete, then 0.1mm bubble diameter of foam concrete, at least 20% higher. Therefore, it is wrong to pursue a bubble diameter of more than 0.1mm, which should be corrected in the production of foamed concrete.

 

4. The lower the foam bleeding rate, the better. Avoid using milk foam.

According to the size of water content, foam is divided into milk foam with more water and sponge foam with more water. Among them, lacteal foam is unqualified inferior foam and cannot be used.

After the foam is made, it gradually secretes water. Its secreting water includes two parts: 

Bleeding of foam liquid film. This water is secreted from the liquid membrane, which is secreted by the liquid membrane under the combined action of gravity drainage, surface tension drainage, and liquid membrane damage drainage. The thicker the liquid film of foam is, the larger the bleeding is. The faster the bubble burst, the more bleeding.

Water between bubbles. This is the water that didn't form the bubble film. The worse the foaming agent and foaming machine’s foaming performance, the more water between bubbles cannot form foam liquid film. They're essentially water that doesn't bubble.


When the foam is bleeding at a high rate, it becomes as thin as float juice, sloshing around and not piling up, and there's a lot of water in the foam. When this foam is added to the cement slurry, the cement slurry becomes very thin, and the foam is very little, the volume of the slurry is small, and the resulting foam concrete density is very high, not technical requirements. 

 

Therefore, latex foam should not be used. The appearance of a technically acceptable foam should be a spongy, compact bubble, piled up like white clouds, like bouncing cotton, and not sloshing. This foam has very little water content. This shows that its foam liquid film is small, the foam is not easy to burst, there is little water between the bubbles, and the amount of bubbles is large, accounting for most of the volume of bubbles. It should be emphasized here that the spongy foam must be a small bubble with a diameter of less than 1mm, rather than a few millimeters, or even dozens of millimeters. Bullae are easy to pile up, also like white clouds, but because of the large diameter of the bullae, also unqualified. 

 

The low secretion of foam is mainly to ensure the number of bubbles in the foam and the porosity of foamed concrete, that is, to ensure the density of foamed concrete. 

 

5. The foam has no side effects on cementitious materials 

The cementitious material is the main source of strength of foamed concrete, the addition of foam cannot affect its cementitious property, that is, there is no negative cementitious effect. Not every bubble can achieve this.

In the long-term test, we discover a lot of foam to cement, magnesite, gesso of gelling have hindrance, can reduce the strength of foam concrete, sometimes even from beginning to end the concrete after hardening loses strength basically, resemble a dish scatters sand.  The stability of these foams is very good, several hours do not disappear, the appearance of sponge, bleeding is very low, dense, and uniform, all aspects meet the technical requirements, but are not compatible with the gel material, so cannot be used for production. This means that foams that are otherwise qualified, such as affecting strength, are ultimately not technically qualified. 

 

Suppliers of Concrete Additives

TRUNNANO is a reliable foaming agents supplier with over 12-year experience in nano-building energy conservation and nanotechnology development.

If you are looking for high-quality CLC foaming agents, please feel free to contact us and send an inquiry. (sales@cabr-concrete.com)

We accept payment via Credit Card, T/T, West Union, and Paypal. TRUNNANO will ship the goods to customers overseas through FedEx, DHL, by air, or by sea.


Prior to the impact of COVID-19 on the chemicals and materials industry and the price of the concrete foaming agent, many industry observers expected low to flat growth in 2021 in all regions outside Asia, with many countries seeing slower growth compared to recent years. Operational excellence has long been a hallmark of the concrete foaming agent chemical industry, and many companies are financially able to withstand short-term dips in end-market demand due to rapid leverage from reduced capex on hand.

The analysis shows that, whatever the final course of the pandemic, we can expect the inevitable long-term effects. Workplaces are expected to slowly return to pre-COVID-19 practices. Companies investing in enterprise-wide digital initiatives saw these "payoffs" in the early pandemic environment. For more information about concrete foaming agent, please feel free to contact us.

Inquery us

Our Latest Answers

Global Chromium Diboride CrB2 Powder,Overview of Chromium Diboride CrB2 Powder,Application of Chromium Diboride CrB2 Powder,Chromium diboride CrB2 powder price,Chromium Diboride CrB2 Powder Supplier market trend 2025-2030 Application of Chromium Diboride

The chemical formula of chromium diboride is CrB2, which is a crystal with high hardness and melting point, and is chemically stable. Concentrated nitric acid is insoluble and can be directly mixed with elements or made from active metal reduction ox…

Global Copper Oxide, Copper Oxide Overview, Copper Oxide Application, Copper Oxide Suppliers, Copper Oxide Price market trend 2023-2029 Is CuO a copper oxide? by Newsmanysmileys

Copper oxide,chemical formula CuO. It is a black oxide of copper,slightly amphoteric and slightly hygroscopic.The relative molecular mass is 79.545,the density is 6.3~6.9 g/cm3,and the melting point is 1026℃.…